Sheetmetal Punches

A quick and easy way to cut clean holes in sheet metal up to 16 gauge.

Special design allows even load during cutting and produces a burr free hole that needs no extra finishing.

Heat treated cutting edges with black anti-corrosive surface finish to prevent rusting.

All punches boxed singly without spanner, which should be ordered separately.

Size.3/4in Square.
Spanner Operated. 5/8in AF.

A quick and easy way to cut clean holes in sheet metal up to 16 gauge.

Special design allows even load during cutting and produces a burr free hole that needs no extra finishing.

Heat treated cutting edges with black anti-corrosive surface finish to prevent rusting.

All punches boxed singly without key, which should be ordered separately.

Size.1in. Square.
Key Type. B Key Operated. 5/16in AF

A quick and easy way to cut clean holes in sheet metal up to 16 gauge.

Special design allows even load during cutting and produces a burr free hole that needs no extra finishing.

Heat treated cutting edges with black anti-corrosive surface finish to prevent rusting.

All punches boxed singly without key, which should be ordered separately.

To use these punches they require a hole to be drilled through the sheet metal (large enough to clear the Allen Screw) then the Die and Allen screw are threaded through the sheet metal then onto the die nut and screw die nut. When the Allen screw is tightened the punch will cut cleanly and evenly through the metal.

Size.1.1/16in.
Key Type.B. 5/16in AF

A quick and easy way to cut clean holes in sheet metal up to 16 gauge.

Special design allows even load during cutting and produces a burr free hole that needs no extra finishing.

Heat treated cutting edges with black anti-corrosive surface finish to prevent rusting.

All punches boxed singly without key, which should be ordered separately.

To use these punches they require a hole to be drilled through the sheet metal (large enough to clear the Allen Screw) then the Die and Allen screw are threaded through the sheet metal then onto the die nut and screw die nut. When the Allen screw is tightened the punch will cut cleanly and evenly through the metal.

Size.1.1/8in.
Key Type.B. 5/16in AF

A quick and easy way to cut clean holes in sheet metal up to 16 gauge.

Special design allows even load during cutting and produces a burr free hole that needs no extra finishing.

Heat treated cutting edges with black anti-corrosive surface finish to prevent rusting.

All punches boxed singly without key, which should be ordered separately.

To use these punches they require a hole to be drilled through the sheet metal (large enough to clear the Allen Screw) then the Die and Allen screw are threaded through the sheet metal then onto the die nut and screw die nut. When the Allen screw is tightened the punch will cut cleanly and evenly through the metal.

Size.1.3/16in.
Key Type.B. 5/16in AF

A quick and easy way to cut clean holes in sheet metal up to 16 gauge.

Special design allows even load during cutting and produces a burr free hole that needs no extra finishing.

Heat treated cutting edges with black anti-corrosive surface finish to prevent rusting.

All punches boxed singly without key, which should be ordered separately.

To use these punches they require a hole to be drilled through the sheet metal (large enough to clear the Allen Screw) then the Die and Allen screw are threaded through the sheet metal then onto the die nut and screw die nut. When the Allen screw is tightened the punch will cut cleanly and evenly through the metal.

Size.1.1/4in.
Key Type.B. 5/16in AF

A quick and easy way to cut clean holes in sheet metal up to 16 gauge.

Special design allows even load during cutting and produces a burr free hole that needs no extra finishing.

Heat treated cutting edges with black anti-corrosive surface finish to prevent rusting.

All punches boxed singly without key, which should be ordered separately.

To use these punches they require a hole to be drilled through the sheet metal (large enough to clear the Allen Screw) then the Die and Allen screw are threaded through the sheet metal then onto the die nut and screw die nut. When the Allen screw is tightened the punch will cut cleanly and evenly through the metal.

Size.1.3/8in.
Key Type.B. 5/16in

A quick and easy way to cut clean holes in sheet metal up to 16 gauge.

Special design allows even load during cutting and produces a burr free hole that needs no extra finishing.

Heat treated cutting edges with black anti-corrosive surface finish to prevent rusting.

All punches boxed singly without key, which should be ordered separately.

To use these punches they require a hole to be drilled through the sheet metal (large enough to clear the Allen Screw) then the Die and Allen screw are threaded through the sheet metal then onto the die nut and screw die nut. When the Allen screw is tightened the punch will cut cleanly and evenly through the metal.

Size.1.1/2in.
Key Type.B. 5/16in AF

A quick and easy way to cut clean holes in sheet metal up to 16 gauge.

Special design allows even load during cutting and produces a burr free hole that needs no extra finishing.

Heat treated cutting edges with black anti-corrosive surface finish to prevent rusting.

All punches boxed singly without key, which should be ordered separately.

To use these punches they require a hole to be drilled through the sheet metal (large enough to clear the Allen Screw) then the Die and Allen screw are threaded through the sheet metal then onto the die nut and screw die nut. When the Allen screw is tightened the punch will cut cleanly and evenly through the metal.

Size.1.5/8in.
Key Type.B. 5/16in

A quick and easy way to cut clean holes in sheet metal up to 16 gauge.

Special design allows even load during cutting and produces a burr free hole that needs no extra finishing.

Heat treated cutting edges with black anti-corrosive surface finish to prevent rusting.

All punches boxed singly without key, which should be ordered separately.

To use these punches they require a hole to be drilled through the sheet metal (large enough to clear the Allen Screw) then the Die and Allen screw are threaded through the sheet metal then onto the die nut and screw die nut. When the Allen screw is tightened the punch will cut cleanly and evenly through the metal.

Size.1.3/4in.
Key Type.B. 5/16in AF

A quick and easy way to cut clean holes in sheet metal up to 16 gauge.

Special design allows even load during cutting and produces a burr free hole that needs no extra finishing.

Heat treated cutting edges with black anti-corrosive surface finish to prevent rusting.

All punches boxed singly without key, which should be ordered separately.

To use these punches they require a hole to be drilled through the sheet metal (large enough to clear the Allen Screw) then the Die and Allen screw are threaded through the sheet metal then onto the die nut and screw die nut. When the Allen screw is tightened the punch will cut cleanly and evenly through the metal.

Size.2.5/8in.
Key Type.E. 1/2in AF

A quick and easy way to cut clean holes in sheet metal up to 16 gauge.

Special design allows even load during cutting and produces a burr free hole that needs no extra finishing.

Heat treated cutting edges with black anti-corrosive surface finish to prevent rusting.

All punches boxed singly without key, which should be ordered separately.

To use these punches they require a hole to be drilled through the sheet metal (large enough to clear the Allen Screw) then the Die and Allen screw are threaded through the sheet metal then onto the die nut and screw die nut. When the Allen screw is tightened the punch will cut cleanly and evenly through the metal.

Size.3/8in.
Key Type.T. 3/16in AF

A quick and easy way to cut clean holes in sheet metal up to 16 gauge.

Special design allows even load during cutting and produces a burr free hole that needs no extra finishing.

Heat treated cutting edges with black anti-corrosive surface finish to prevent rusting.

All punches boxed singly without key, which should be ordered separately.

To use these punches they require a hole to be drilled through the sheet metal (large enough to clear the Allen Screw) then the Die and Allen screw are threaded through the sheet metal then onto the die nut and screw die nut. When the Allen screw is tightened the punch will cut cleanly and evenly through the metal.

Size.7/16in.
Key Type. T. 3/16in AF

A quick and easy way to cut clean holes in sheet metal up to 16 gauge.

Special design allows even load during cutting and produces a burr free hole that needs no extra finishing.

Heat treated cutting edges with black anti-corrosive surface finish to prevent rusting.

All punches boxed singly without key, which should be ordered separately.

To use these punches they require a hole to be drilled through the sheet metal (large enough to clear the Allen Screw) then the Die and Allen screw are threaded through the sheet metal then onto the die nut and screw die nut. When the Allen screw is tightened the punch will cut cleanly and evenly through the metal.

Size.1/2in.
Key Type.A. 7/32in AF

A quick and easy way to cut clean holes in sheet metal up to 16 gauge.

Special design allows even load during cutting and produces a burr free hole that needs no extra finishing.

Heat treated cutting edges with black anti-corrosive surface finish to prevent rusting.

All punches boxed singly without key, which should be ordered separately.

To use these punches they require a hole to be drilled through the sheet metal (large enough to clear the Allen Screw) then the Die and Allen screw are threaded through the sheet metal then onto the die nut and screw die nut. When the Allen screw is tightened the punch will cut cleanly and evenly through the metal.

Size.9/16in.
Key Type. A. 7/32in AF

A quick and easy way to cut clean holes in sheet metal up to 16 gauge.

Special design allows even load during cutting and produces a burr free hole that needs no extra finishing.

Heat treated cutting edges with black anti-corrosive surface finish to prevent rusting.

All punches boxed singly without key, which should be ordered separately.

To use these punches they require a hole to be drilled through the sheet metal (large enough to clear the Allen Screw) then the Die and Allen screw are threaded through the sheet metal then onto the die nut and screw die nut. When the Allen screw is tightened the punch will cut cleanly and evenly through the metal.

Size.5/8in.
Key Type. A. 7/32in AF

A quick and easy way to cut clean holes in sheet metal up to 16 gauge.

Special design allows even load during cutting and produces a burr free hole that needs no extra finishing.

Heat treated cutting edges with black anti-corrosive surface finish to prevent rusting.

All punches boxed singly without key, which should be ordered separately.

To use these punches they require a hole to be drilled through the sheet metal (large enough to clear the Allen Screw) then the Die and Allen screw are threaded through the sheet metal then onto the die nut and screw die nut. When the Allen screw is tightened the punch will cut cleanly and evenly through the metal.

Size.11/16in.
Key Type.A. 7/32in AF

A quick and easy way to cut clean holes in sheet metal up to 16 gauge.

Special design allows even load during cutting and produces a burr free hole that needs no extra finishing.

Heat treated cutting edges with black anti-corrosive surface finish to prevent rusting.

All punches boxed singly without key, which should be ordered separately.

To use these punches they require a hole to be drilled through the sheet metal (large enough to clear the Allen Screw) then the Die and Allen screw are threaded through the sheet metal then onto the die nut and screw die nut. When the Allen screw is tightened the punch will cut cleanly and evenly through the metal.

Size.3/4in.
Key Type. A.7/32in AF

A quick and easy way to cut clean holes in sheet metal up to 16 gauge.

Special design allows even load during cutting and produces a burr free hole that needs no extra finishing.

Heat treated cutting edges with black anti-corrosive surface finish to prevent rusting.

All punches boxed singly without key, which should be ordered separately.

To use these punches they require a hole to be drilled through the sheet metal (large enough to clear the Allen Screw) then the Die and Allen screw are threaded through the sheet metal then onto the die nut and screw die nut. When the Allen screw is tightened the punch will cut cleanly and evenly through the metal.

Size.13/16in.
Key Type.A. 7/32in AF

A quick and easy way to cut clean holes in sheet metal up to 16 gauge.

Special design allows even load during cutting and produces a burr free hole that needs no extra finishing.

Heat treated cutting edges with black anti-corrosive surface finish to prevent rusting.

All punches boxed singly without key, which should be ordered separately.

To use these punches they require a hole to be drilled through the sheet metal (large enough to clear the Allen Screw) then the Die and Allen screw are threaded through the sheet metal then onto the die nut and screw die nut. When the Allen screw is tightened the punch will cut cleanly and evenly through the metal.

Size.7/8in.
Key Type.A. 7/32in AF

A quick and easy way to cut clean holes in sheet metal up to 16 gauge.

Special design allows even load during cutting and produces a burr free hole that needs no extra finishing.

Heat treated cutting edges with black anti-corrosive surface finish to prevent rusting.

All punches boxed singly without key, which should be ordered separately.

To use these punches they require a hole to be drilled through the sheet metal (large enough to clear the Allen Screw) then the Die and Allen screw are threaded through the sheet metal then onto the die nut and screw die nut. When the Allen screw is tightened the punch will cut cleanly and evenly through the metal.

Size.1in.
Key Type.B. 5/16in AF

A quick and easy way to cut clean holes in sheet metal up to 16 gauge.

Special design allows even load during cutting and produces a burr free hole that needs no extra finishing.

Heat treated cutting edges with black anti-corrosive surface finish to prevent rusting.

All punches are sold singly without key, which should be ordered separately.

Thread the punch onto the Allen screw and then pass the Allen screw through the hole. Position the die on top of the die nut and then screw the die nut onto the projecting Allen screw until it touches the metal sheet.  Use an Allen key to turn the Allen screw.  The screw will pull the punch through the metal and a hole will result.

Please note these instructions apply to cutters up to 15mm in size, for cutters 15mm and over have a different configuration.  Notably they have fewer components, in the larger cutters the thread is in the punch and thus there is no die nut.

Size.10.0mm.
Key Type.MT. 5mm

A quick and easy way to cut clean holes in sheet metal up to 16 gauge.

Special design allows even load during cutting and produces a burr free hole that needs no extra finishing.

Heat treated cutting edges with black anti-corrosive surface finish to prevent rusting.

All punches are sold singly without key, which should be ordered separately.

Thread the punch onto the Allen screw and then pass the Allen screw through the hole. Position the die on top of the die nut and then screw the die nut onto the projecting Allen screw until it touches the metal sheet.  Use an Allen key to turn the Allen screw.  The screw will pull the punch through the metal and a hole will result.

Please note these instructions apply to cutters up to 15mm in size, for cutters 15mm and over have a different configuration.  Notably they have fewer components, in the larger cutters the thread is in the punch and thus there is no die nut.

Size.11.0mm.
Key Type.MT. 5mm

A quick and easy way to cut clean holes in sheet metal up to 16 gauge.

Special design allows even load during cutting and produces a burr free hole that needs no extra finishing.

Heat treated cutting edges with black anti-corrosive surface finish to prevent rusting.

All punches are sold singly without key, which should be ordered separately.

Thread the punch onto the Allen screw and then pass the Allen screw through the hole. Position the die on top of the die nut and then screw the die nut onto the projecting Allen screw until it touches the metal sheet.  Use an Allen key to turn the Allen screw.  The screw will pull the punch through the metal and a hole will result.

Please note these instructions apply to cutters up to 15mm in size, for cutters 15mm and over have a different configuration.  Notably they have fewer components, in the larger cutters the thread is in the punch and thus there is no die nut.

Size.12.5mm.
Key Type.MA. 6mm

A quick and easy way to cut clean holes in sheet metal up to 16 gauge.

Special design allows even load during cutting and produces a burr free hole that needs no extra finishing.

Heat treated cutting edges with black anti-corrosive surface finish to prevent rusting.

All punches are sold singly without key, which should be ordered separately.

Thread the punch onto the Allen screw and then pass the Allen screw through the hole. Position the die on top of the die nut and then screw the die nut onto the projecting Allen screw until it touches the metal sheet.  Use an Allen key to turn the Allen screw.  The screw will pull the punch through the metal and a hole will result.

Please note these instructions apply to cutters up to 15mm in size, for cutters 15mm and over have a different configuration.  Notably they have fewer components, in the larger cutters the thread is in the punch and thus there is no die nut.

Size.12.7mm.
Key Type. MA. 6mm

A quick and easy way to cut clean holes in sheet metal up to 16 gauge.

Special design allows even load during cutting and produces a burr free hole that needs no extra finishing.

Heat treated cutting edges with black anti-corrosive surface finish to prevent rusting.

All punches are sold singly without key, which should be ordered separately.

Thread the punch onto the Allen screw and then pass the Allen screw through the hole. Position the die on top of the die nut and then screw the die nut onto the projecting Allen screw until it touches the metal sheet.  Use an Allen key to turn the Allen screw.  The screw will pull the punch through the metal and a hole will result.

Please note these instructions apply to cutters up to 15mm in size, for cutters 15mm and over have a different configuration.  Notably they have fewer components, in the larger cutters the thread is in the punch and thus there is no die nut.

Size.14.0mm.
Key Type. MA. 6mm

A quick and easy way to cut clean holes in sheet metal up to 16 gauge.

Special design allows even load during cutting and produces a burr free hole that needs no extra finishing.

Heat treated cutting edges with black anti-corrosive surface finish to prevent rusting.

All punches are sold singly without key, which should be ordered separately.

Thread the punch onto the Allen screw and then pass the Allen screw through the hole. Position the die on top of the die nut and then screw the die nut onto the projecting Allen screw until it touches the metal sheet.  Use an Allen key to turn the Allen screw.  The screw will pull the punch through the metal and a hole will result.

Please note these instructions apply to cutters up to 15mm in size, for cutters 15mm and over have a different configuration.  Notably they have fewer components, in the larger cutters the thread is in the punch and thus there is no die nut.

Size.15.0mm.
Key Type.MA. 6mm

A quick and easy way to cut clean holes in sheet metal up to 16 gauge.

Special design allows even load during cutting and produces a burr free hole that needs no extra finishing.

Heat treated cutting edges with black anti-corrosive surface finish to prevent rusting.

All punches are sold singly without key, which should be ordered separately.

Thread the punch onto the Allen screw and then pass the Allen screw through the hole. Position the die on top of the die nut and then screw the die nut onto the projecting Allen screw until it touches the metal sheet.  Use an Allen key to turn the Allen screw.  The screw will pull the punch through the metal and a hole will result.

Please note these instructions apply to cutters up to 15mm in size, for cutters 15mm and over have a different configuration.  Notably they have fewer components, in the larger cutters the thread is in the punch and thus there is no die nut.

Size.15.2mm.
Key Type.MA. 6mm

A quick and easy way to cut clean holes in sheet metal up to 16 gauge.

Special design allows even load during cutting and produces a burr free hole that needs no extra finishing.

Heat treated cutting edges with black anti-corrosive surface finish to prevent rusting.

All punches are sold singly without key, which should be ordered separately.

Thread the punch onto the Allen screw and then pass the Allen screw through the hole. Position the die on top of the die nut and then screw the die nut onto the projecting Allen screw until it touches the metal sheet.  Use an Allen key to turn the Allen screw.  The screw will pull the punch through the metal and a hole will result.

Please note these instructions apply to cutters up to 15mm in size, for cutters 15mm and over have a different configuration.  Notably they have fewer components, in the larger cutters the thread is in the punch and thus there is no die nut.

Size.16.0mm.
Key Type.MA. 6mm

A quick and easy way to cut clean holes in sheet metal up to 16 gauge.

Special design allows even load during cutting and produces a burr free hole that needs no extra finishing.

Heat treated cutting edges with black anti-corrosive surface finish to prevent rusting.

All punches are sold singly without key, which should be ordered separately.

Thread the punch onto the Allen screw and then pass the Allen screw through the hole. Position the die on top of the die nut and then screw the die nut onto the projecting Allen screw until it touches the metal sheet.  Use an Allen key to turn the Allen screw.  The screw will pull the punch through the metal and a hole will result.

Please note these instructions apply to cutters up to 15mm in size, for cutters 15mm and over have a different configuration.  Notably they have fewer components, in the larger cutters the thread is in the punch and thus there is no die nut.

Size.18.6mm.
Key Type. MB. 8mm

A quick and easy way to cut clean holes in sheet metal up to 16 gauge.

Special design allows even load during cutting and produces a burr free hole that needs no extra finishing.

Heat treated cutting edges with black anti-corrosive surface finish to prevent rusting.

All punches are sold singly without key, which should be ordered separately.

Thread the punch onto the Allen screw and then pass the Allen screw through the hole. Position the die on top of the die nut and then screw the die nut onto the projecting Allen screw until it touches the metal sheet.  Use an Allen key to turn the Allen screw.  The screw will pull the punch through the metal and a hole will result.

Please note these instructions apply to cutters up to 15mm in size, for cutters 15mm and over have a different configuration.  Notably they have fewer components, in the larger cutters the thread is in the punch and thus there is no die nut.

Size.19.0mm.
Key Type.MB. 8mm

A quick and easy way to cut clean holes in sheet metal up to 16 gauge.

Special design allows even load during cutting and produces a burr free hole that needs no extra finishing.

Heat treated cutting edges with black anti-corrosive surface finish to prevent rusting.

All punches boxed singly without spanner, which should be ordered separately.

Size.19.0mm.Square.
Spanner Operated 5/8in AF.

A quick and easy way to cut clean holes in sheet metal up to 16 gauge.

Special design allows even load during cutting and produces a burr free hole that needs no extra finishing.

Heat treated cutting edges with black anti-corrosive surface finish to prevent rusting.

All punches are sold singly without key, which should be ordered separately.

Thread the punch onto the Allen screw and then pass the Allen screw through the hole. Position the die on top of the die nut and then screw the die nut onto the projecting Allen screw until it touches the metal sheet.  Use an Allen key to turn the Allen screw.  The screw will pull the punch through the metal and a hole will result.

Please note these instructions apply to cutters up to 15mm in size, for cutters 15mm and over have a different configuration.  Notably they have fewer components, in the larger cutters the thread is in the punch and thus there is no die nut.

Size.20.0mm.
Key Type.MB.8mm

A quick and easy way to cut clean holes in sheet metal up to 16 gauge.

Special design allows even load during cutting and produces a burr free hole that needs no extra finishing.

Heat treated cutting edges with black anti-corrosive surface finish to prevent rusting.

All punches are sold singly without key, which should be ordered separately.

Thread the punch onto the Allen screw and then pass the Allen screw through the hole. Position the die on top of the die nut and then screw the die nut onto the projecting Allen screw until it touches the metal sheet.  Use an Allen key to turn the Allen screw.  The screw will pull the punch through the metal and a hole will result.

Please note these instructions apply to cutters up to 15mm in size, for cutters 15mm and over have a different configuration.  Notably they have fewer components, in the larger cutters the thread is in the punch and thus there is no die nut.

Size.20.4mm.
Key Type.MB. 8mm

A quick and easy way to cut clean holes in sheet metal up to 16 gauge.

Special design allows even load during cutting and produces a burr free hole that needs no extra finishing.

Heat treated cutting edges with black anti-corrosive surface finish to prevent rusting.

All punches are sold singly without key, which should be ordered separately.

Thread the punch onto the Allen screw and then pass the Allen screw through the hole. Position the die on top of the die nut and then screw the die nut onto the projecting Allen screw until it touches the metal sheet.  Use an Allen key to turn the Allen screw.  The screw will pull the punch through the metal and a hole will result.

Please note these instructions apply to cutters up to 15mm in size, for cutters 15mm and over have a different configuration.  Notably they have fewer components, in the larger cutters the thread is in the punch and thus there is no die nut.

Size.21.0mm.
Key Type.MB.8mm

A quick and easy way to cut clean holes in sheet metal up to 16 gauge.

Special design allows even load during cutting and produces a burr free hole that needs no extra finishing.

Heat treated cutting edges with black anti-corrosive surface finish to prevent rusting.

All punches are sold singly without key, which should be ordered separately.

Thread the punch onto the Allen screw and then pass the Allen screw through the hole. Position the die on top of the die nut and then screw the die nut onto the projecting Allen screw until it touches the metal sheet.  Use an Allen key to turn the Allen screw.  The screw will pull the punch through the metal and a hole will result.

Please note these instructions apply to cutters up to 15mm in size, for cutters 15mm and over have a different configuration.  Notably they have fewer components, in the larger cutters the thread is in the punch and thus there is no die nut.

Size.22.5mm.
Key Type.MB. 8mm

A quick and easy way to cut clean holes in sheet metal up to 16 gauge.

Special design allows even load during cutting and produces a burr free hole that needs no extra finishing.

Heat treated cutting edges with black anti-corrosive surface finish to prevent rusting.

All punches are sold singly without key, which should be ordered separately.

Thread the punch onto the Allen screw and then pass the Allen screw through the hole. Position the die on top of the die nut and then screw the die nut onto the projecting Allen screw until it touches the metal sheet.  Use an Allen key to turn the Allen screw.  The screw will pull the punch through the metal and a hole will result.

Please note these instructions apply to cutters up to 15mm in size, for cutters 15mm and over have a different configuration.  Notably they have fewer components, in the larger cutters the thread is in the punch and thus there is no die nut.

Size.24.0mm.
Key Type.MB.8mm

A quick and easy way to cut clean holes in sheet metal up to 16 gauge.

Special design allows even load during cutting and produces a burr free hole that needs no extra finishing.

Heat treated cutting edges with black anti-corrosive surface finish to prevent rusting.

All punches are sold singly without key, which should be ordered separately.

Thread the punch onto the Allen screw and then pass the Allen screw through the hole. Position the die on top of the die nut and then screw the die nut onto the projecting Allen screw until it touches the metal sheet.  Use an Allen key to turn the Allen screw.  The screw will pull the punch through the metal and a hole will result.

Please note these instructions apply to cutters up to 15mm in size, for cutters 15mm and over have a different configuration.  Notably they have fewer components, in the larger cutters the thread is in the punch and thus there is no die nut.

Size.25.0mm.
Key Type.MB. 8mm

A quick and easy way to cut clean holes in sheet metal up to 16 gauge.

Special design allows even load during cutting and produces a burr free hole that needs no extra finishing.

Heat treated cutting edges with black anti-corrosive surface finish to prevent rusting.

All punches boxed singly without spanner, which should be ordered separately.

Size.25.4mm.Square.
Key Type. B Key Operated. 5/16in

A quick and easy way to cut clean holes in sheet metal up to 16 gauge.

Special design allows even load during cutting and produces a burr free hole that needs no extra finishing.

Heat treated cutting edges with black anti-corrosive surface finish to prevent rusting.

All punches are sold singly without key, which should be ordered separately.

Thread the punch onto the Allen screw and then pass the Allen screw through the hole. Position the die on top of the die nut and then screw the die nut onto the projecting Allen screw until it touches the metal sheet.  Use an Allen key to turn the Allen screw.  The screw will pull the punch through the metal and a hole will result.

Please note these instructions apply to cutters up to 15mm in size, for cutters 15mm and over have a different configuration.  Notably they have fewer components, in the larger cutters the thread is in the punch and thus there is no die nut.

Size.27.5mm.
Key Type.MB. 8mm

A quick and easy way to cut clean holes in sheet metal up to 16 gauge.

Special design allows even load during cutting and produces a burr free hole that needs no extra finishing.

Heat treated cutting edges with black anti-corrosive surface finish to prevent rusting.

All punches are sold singly without key, which should be ordered separately.

Thread the punch onto the Allen screw and then pass the Allen screw through the hole. Position the die on top of the die nut and then screw the die nut onto the projecting Allen screw until it touches the metal sheet.  Use an Allen key to turn the Allen screw.  The screw will pull the punch through the metal and a hole will result.

Please note these instructions apply to cutters up to 15mm in size, for cutters 15mm and over have a different configuration.  Notably they have fewer components, in the larger cutters the thread is in the punch and thus there is no die nut.

Size.28.3mm.
Key Type.MB. 8mm

A quick and easy way to cut clean holes in sheet metal up to 16 gauge.

Special design allows even load during cutting and produces a burr free hole that needs no extra finishing.

Heat treated cutting edges with black anti-corrosive surface finish to prevent rusting.

All punches are sold singly without key, which should be ordered separately.

Thread the punch onto the Allen screw and then pass the Allen screw through the hole. Position the die on top of the die nut and then screw the die nut onto the projecting Allen screw until it touches the metal sheet.  Use an Allen key to turn the Allen screw.  The screw will pull the punch through the metal and a hole will result.

Please note these instructions apply to cutters up to 15mm in size, for cutters 15mm and over have a different configuration.  Notably they have fewer components, in the larger cutters the thread is in the punch and thus there is no die nut.

Size.29.0mm.
Key Type.MB. 8mm

A quick and easy way to cut clean holes in sheet metal up to 16 gauge.

Special design allows even load during cutting and produces a burr free hole that needs no extra finishing.

Heat treated cutting edges with black anti-corrosive surface finish to prevent rusting.

All punches are sold singly without key, which should be ordered separately.

Thread the punch onto the Allen screw and then pass the Allen screw through the hole. Position the die on top of the die nut and then screw the die nut onto the projecting Allen screw until it touches the metal sheet.  Use an Allen key to turn the Allen screw.  The screw will pull the punch through the metal and a hole will result.

Please note these instructions apply to cutters up to 15mm in size, for cutters 15mm and over have a different configuration.  Notably they have fewer components, in the larger cutters the thread is in the punch and thus there is no die nut.

Size.30.0mm.
Key Type.MB.8mm

A quick and easy way to cut clean holes in sheet metal up to 16 gauge.

Special design allows even load during cutting and produces a burr free hole that needs no extra finishing.

Heat treated cutting edges with black anti-corrosive surface finish to prevent rusting.

All punches are sold singly without key, which should be ordered separately.

Thread the punch onto the Allen screw and then pass the Allen screw through the hole. Position the die on top of the die nut and then screw the die nut onto the projecting Allen screw until it touches the metal sheet.  Use an Allen key to turn the Allen screw.  The screw will pull the punch through the metal and a hole will result.

Please note these instructions apply to cutters up to 15mm in size, for cutters 15mm and over have a different configuration.  Notably they have fewer components, in the larger cutters the thread is in the punch and thus there is no die nut.

Size.31.0mm.
Key Type.MB. 8mm

A quick and easy way to cut clean holes in sheet metal up to 16 gauge.

Special design allows even load during cutting and produces a burr free hole that needs no extra finishing.

Heat treated cutting edges with black anti-corrosive surface finish to prevent rusting.

All punches are sold singly without key, which should be ordered separately.

Thread the punch onto the Allen screw and then pass the Allen screw through the hole. Position the die on top of the die nut and then screw the die nut onto the projecting Allen screw until it touches the metal sheet.  Use an Allen key to turn the Allen screw.  The screw will pull the punch through the metal and a hole will result.

Please note these instructions apply to cutters up to 15mm in size, for cutters 15mm and over have a different configuration.  Notably they have fewer components, in the larger cutters the thread is in the punch and thus there is no die nut.

Size.32.5mm.
Key Type.MC. 10mm

A quick and easy way to cut clean holes in sheet metal up to 16 gauge.

Special design allows even load during cutting and produces a burr free hole that needs no extra finishing.

Heat treated cutting edges with black anti-corrosive surface finish to prevent rusting.

All punches are sold singly without key, which should be ordered separately.

Thread the punch onto the Allen screw and then pass the Allen screw through the hole. Position the die on top of the die nut and then screw the die nut onto the projecting Allen screw until it touches the metal sheet.  Use an Allen key to turn the Allen screw.  The screw will pull the punch through the metal and a hole will result.

Please note these instructions apply to cutters up to 15mm in size, for cutters 15mm and over have a different configuration.  Notably they have fewer components, in the larger cutters the thread is in the punch and thus there is no die nut.

Size.34.0mm.
Key Type.MC. 10mm

A quick and easy way to cut clean holes in sheet metal up to 16 gauge.

Special design allows even load during cutting and produces a burr free hole that needs no extra finishing.

Heat treated cutting edges with black anti-corrosive surface finish to prevent rusting.

All punches are sold singly without key, which should be ordered separately.

Thread the punch onto the Allen screw and then pass the Allen screw through the hole. Position the die on top of the die nut and then screw the die nut onto the projecting Allen screw until it touches the metal sheet.  Use an Allen key to turn the Allen screw.  The screw will pull the punch through the metal and a hole will result.

Please note these instructions apply to cutters up to 15mm in size, for cutters 15mm and over have a different configuration.  Notably they have fewer components, in the larger cutters the thread is in the punch and thus there is no die nut.

Size.35.0mm.
Key Type.MC. 10mm

A quick and easy way to cut clean holes in sheet metal up to 16 gauge.

Special design allows even load during cutting and produces a burr free hole that needs no extra finishing.

Heat treated cutting edges with black anti-corrosive surface finish to prevent rusting.

All punches are sold singly without key, which should be ordered separately.

Thread the punch onto the Allen screw and then pass the Allen screw through the hole. Position the die on top of the die nut and then screw the die nut onto the projecting Allen screw until it touches the metal sheet.  Use an Allen key to turn the Allen screw.  The screw will pull the punch through the metal and a hole will result.

Please note these instructions apply to cutters up to 15mm in size, for cutters 15mm and over have a different configuration.  Notably they have fewer components, in the larger cutters the thread is in the punch and thus there is no die nut.

Size.37.0mm.
Key Type.MC. 10mm

A quick and easy way to cut clean holes in sheet metal up to 16 gauge.

Special design allows even load during cutting and produces a burr free hole that needs no extra finishing.

Heat treated cutting edges with black anti-corrosive surface finish to prevent rusting.

All punches are sold singly without key, which should be ordered separately.

Thread the punch onto the Allen screw and then pass the Allen screw through the hole. Position the die on top of the die nut and then screw the die nut onto the projecting Allen screw until it touches the metal sheet.  Use an Allen key to turn the Allen screw.  The screw will pull the punch through the metal and a hole will result.

Please note these instructions apply to cutters up to 15mm in size, for cutters 15mm and over have a different configuration.  Notably they have fewer components, in the larger cutters the thread is in the punch and thus there is no die nut.

Size.37.5mm.
Key Type. MC. 10mm

A quick and easy way to cut clean holes in sheet metal up to 16 gauge.

Special design allows even load during cutting and produces a burr free hole that needs no extra finishing.

Heat treated cutting edges with black anti-corrosive surface finish to prevent rusting.

All punches are sold singly without key, which should be ordered separately.

Thread the punch onto the Allen screw and then pass the Allen screw through the hole. Position the die on top of the die nut and then screw the die nut onto the projecting Allen screw until it touches the metal sheet.  Use an Allen key to turn the Allen screw.  The screw will pull the punch through the metal and a hole will result.

Please note these instructions apply to cutters up to 15mm in size, for cutters 15mm and over have a different configuration.  Notably they have fewer components, in the larger cutters the thread is in the punch and thus there is no die nut.

Size.40.0mm.
Key Type.MC. 10mm

A quick and easy way to cut clean holes in sheet metal up to 16 gauge.

Special design allows even load during cutting and produces a burr free hole that needs no extra finishing.

Heat treated cutting edges with black anti-corrosive surface finish to prevent rusting.

All punches are sold singly without key, which should be ordered separately.

Thread the punch onto the Allen screw and then pass the Allen screw through the hole. Position the die on top of the die nut and then screw the die nut onto the projecting Allen screw until it touches the metal sheet.  Use an Allen key to turn the Allen screw.  The screw will pull the punch through the metal and a hole will result.

Please note these instructions apply to cutters up to 15mm in size, for cutters 15mm and over have a different configuration.  Notably they have fewer components, in the larger cutters the thread is in the punch and thus there is no die nut.

Size. 45.0mm.
Key Type. MC. 10mm

A quick and easy way to cut clean holes in sheet metal up to 16 gauge.

Special design allows even load during cutting and produces a burr free hole that needs no extra finishing.

Heat treated cutting edges with black anti-corrosive surface finish to prevent rusting.

All punches are sold singly without key, which should be ordered separately.

Thread the punch onto the Allen screw and then pass the Allen screw through the hole. Position the die on top of the die nut and then screw the die nut onto the projecting Allen screw until it touches the metal sheet.  Use an Allen key to turn the Allen screw.  The screw will pull the punch through the metal and a hole will result.

Please note these instructions apply to cutters up to 15mm in size, for cutters 15mm and over have a different configuration.  Notably they have fewer components, in the larger cutters the thread is in the punch and thus there is no die nut.

Size.47.0mm.
Key Type.MC. 10mm

A quick and easy way to cut clean holes in sheet metal up to 16 gauge.

Special design allows even load during cutting and produces a burr free hole that needs no extra finishing.

Heat treated cutting edges with black anti-corrosive surface finish to prevent rusting.

All punches are sold singly without key, which should be ordered separately.

Thread the punch onto the Allen screw and then pass the Allen screw through the hole. Position the die on top of the die nut and then screw the die nut onto the projecting Allen screw until it touches the metal sheet.  Use an Allen key to turn the Allen screw.  The screw will pull the punch through the metal and a hole will result.

Please note these instructions apply to cutters up to 15mm in size, for cutters 15mm and over have a different configuration.  Notably they have fewer components, in the larger cutters the thread is in the punch and thus there is no die nut.

Size.48.0mm.
Key Type. MC. 10mm

A quick and easy way to cut clean holes in sheet metal up to 16 gauge.

Special design allows even load during cutting and produces a burr free hole that needs no extra finishing.

Heat treated cutting edges with black anti-corrosive surface finish to prevent rusting.

All punches are sold singly without key, which should be ordered separately.

Thread the punch onto the Allen screw and then pass the Allen screw through the hole. Position the die on top of the die nut and then screw the die nut onto the projecting Allen screw until it touches the metal sheet.  Use an Allen key to turn the Allen screw.  The screw will pull the punch through the metal and a hole will result.

Please note these instructions apply to cutters up to 15mm in size, for cutters 15mm and over have a different configuration.  Notably they have fewer components, in the larger cutters the thread is in the punch and thus there is no die nut.

Size. 50.0mm.
Key Type. MC. 10mm

A quick and easy way to cut clean holes in sheet metal up to 16 gauge.

Special design allows even load during cutting and produces a burr free hole that needs no extra finishing.

Heat treated cutting edges with black anti-corrosive surface finish to prevent rusting.

All punches are sold singly without key, which should be ordered separately.

Thread the punch onto the Allen screw and then pass the Allen screw through the hole. Position the die on top of the die nut and then screw the die nut onto the projecting Allen screw until it touches the metal sheet.  Use an Allen key to turn the Allen screw.  The screw will pull the punch through the metal and a hole will result.

Please note these instructions apply to cutters up to 15mm in size, for cutters 15mm and over have a different configuration.  Notably they have fewer components, in the larger cutters the thread is in the punch and thus there is no die nut.

Size.51.0mm.
Key Type.MC. 10mm

A quick and easy way to cut clean holes in sheet metal up to 16 gauge.

Special design allows even load during cutting and produces a burr free hole that needs no extra finishing.

Heat treated cutting edges with black anti-corrosive surface finish to prevent rusting.

All punches are sold singly without key, which should be ordered separately.

Thread the punch onto the Allen screw and then pass the Allen screw through the hole. Position the die on top of the die nut and then screw the die nut onto the projecting Allen screw until it touches the metal sheet.  Use an Allen key to turn the Allen screw.  The screw will pull the punch through the metal and a hole will result.

Please note these instructions apply to cutters up to 15mm in size, for cutters 15mm and over have a different configuration.  Notably they have fewer components, in the larger cutters the thread is in the punch and thus there is no die nut.

Size.52.0mm.
Key Type.ME. 14mm

A quick and easy way to cut clean holes in sheet metal up to 16 gauge.

Special design allows even load during cutting and produces a burr free hole that needs no extra finishing.

Heat treated cutting edges with black anti-corrosive surface finish to prevent rusting.

All punches are sold singly without key, which should be ordered separately.

Thread the punch onto the Allen screw and then pass the Allen screw through the hole. Position the die on top of the die nut and then screw the die nut onto the projecting Allen screw until it touches the metal sheet.  Use an Allen key to turn the Allen screw.  The screw will pull the punch through the metal and a hole will result.

Please note these instructions apply to cutters up to 15mm in size, for cutters 15mm and over have a different configuration.  Notably they have fewer components, in the larger cutters the thread is in the punch and thus there is no die nut.

Size.54.0mm
Key Type.ME. 14mm

A quick and easy way to cut clean holes in sheet metal up to 16 gauge.

Special design allows even load during cutting and produces a burr free hole that needs no extra finishing.

Heat treated cutting edges with black anti-corrosive surface finish to prevent rusting.

All punches are sold singly without key, which should be ordered separately.

Thread the punch onto the Allen screw and then pass the Allen screw through the hole. Position the die on top of the die nut and then screw the die nut onto the projecting Allen screw until it touches the metal sheet.  Use an Allen key to turn the Allen screw.  The screw will pull the punch through the metal and a hole will result.

Please note these instructions apply to cutters up to 15mm in size, for cutters 15mm and over have a different configuration.  Notably they have fewer components, in the larger cutters the thread is in the punch and thus there is no die nut.

Size.55.0mm.
Key Type. ME. 14mm

A quick and easy way to cut clean holes in sheet metal up to 16 gauge.

Special design allows even load during cutting and produces a burr free hole that needs no extra finishing.

Heat treated cutting edges with black anti-corrosive surface finish to prevent rusting.

All punches are sold singly without key, which should be ordered separately.

Thread the punch onto the Allen screw and then pass the Allen screw through the hole. Position the die on top of the die nut and then screw the die nut onto the projecting Allen screw until it touches the metal sheet.  Use an Allen key to turn the Allen screw.  The screw will pull the punch through the metal and a hole will result.

Please note these instructions apply to cutters up to 15mm in size, for cutters 15mm and over have a different configuration.  Notably they have fewer components, in the larger cutters the thread is in the punch and thus there is no die nut.

Size.60.0mm.
Key Type. ME. 14mm

A quick and easy way to cut clean holes in sheet metal up to 16 gauge.

Special design allows even load during cutting and produces a burr free hole that needs no extra finishing.

Heat treated cutting edges with black anti-corrosive surface finish to prevent rusting.

All punches are sold singly without key, which should be ordered separately.

Thread the punch onto the Allen screw and then pass the Allen screw through the hole. Position the die on top of the die nut and then screw the die nut onto the projecting Allen screw until it touches the metal sheet.  Use an Allen key to turn the Allen screw.  The screw will pull the punch through the metal and a hole will result.

Please note these instructions apply to cutters up to 15mm in size, for cutters 15mm and over have a different configuration.  Notably they have fewer components, in the larger cutters the thread is in the punch and thus there is no die nut.

Size.64.0mm.
Key Type.ME. 14mm

A quick and easy way to cut clean holes in sheet metal up to 16 gauge.

Special design allows even load during cutting and produces a burr free hole that needs no extra finishing.

Heat treated cutting edges with black anti-corrosive surface finish to prevent rusting.

All punches are sold singly without key, which should be ordered separately.

Thread the punch onto the Allen screw and then pass the Allen screw through the hole. Position the die on top of the die nut and then screw the die nut onto the projecting Allen screw until it touches the metal sheet.  Use an Allen key to turn the Allen screw.  The screw will pull the punch through the metal and a hole will result.

Please note these instructions apply to cutters up to 15mm in size, for cutters 15mm and over have a different configuration.  Notably they have fewer components, in the larger cutters the thread is in the punch and thus there is no die nut.

Size.65.0mm.
Key Type.ME. 14mm

A quick and easy way to cut clean holes in sheet metal up to 16 gauge.

Special design allows even load during cutting and produces a burr free hole that needs no extra finishing.

Heat treated cutting edges with black anti-corrosive surface finish to prevent rusting.

All punches are sold singly without key, which should be ordered separately.

Thread the punch onto the Allen screw and then pass the Allen screw through the hole. Position the die on top of the die nut and then screw the die nut onto the projecting Allen screw until it touches the metal sheet.  Use an Allen key to turn the Allen screw.  The screw will pull the punch through the metal and a hole will result.

Please note these instructions apply to cutters up to 15mm in size, for cutters 15mm and over have a different configuration.  Notably they have fewer components, in the larger cutters the thread is in the punch and thus there is no die nut.

Size.70.0mm.
Key Type.ME. 14mm

A quick and easy way to cut clean holes in sheet metal up to 16 gauge.

Special design allows even load during cutting and produces a burr free hole that needs no extra finishing.

Heat treated cutting edges with black anti-corrosive surface finish to prevent rusting.

All punches are sold singly without key, which should be ordered separately.

Thread the punch onto the Allen screw and then pass the Allen screw through the hole. Position the die on top of the die nut and then screw the die nut onto the projecting Allen screw until it touches the metal sheet.  Use an Allen key to turn the Allen screw.  The screw will pull the punch through the metal and a hole will result.

Please note these instructions apply to cutters up to 15mm in size, for cutters 15mm and over have a different configuration.  Notably they have fewer components, in the larger cutters the thread is in the punch and thus there is no die nut.

Size.75.0mm.
Key Type. ME.14mm

A quick and easy way to cut clean holes in sheet metal up to 16 gauge.

Special design allows even load during cutting and produces a burr free hole that needs no extra finishing.

Heat treated cutting edges with black anti-corrosive surface finish to prevent rusting.

All punches are sold singly without key, which should be ordered separately.

Thread the punch onto the Allen screw and then pass the Allen screw through the hole. Position the die on top of the die nut and then screw the die nut onto the projecting Allen screw until it touches the metal sheet.  Use an Allen key to turn the Allen screw.  The screw will pull the punch through the metal and a hole will result.

Please note these instructions apply to cutters up to 15mm in size, for cutters 15mm and over have a different configuration.  Notably they have fewer components, in the larger cutters the thread is in the punch and thus there is no die nut.

Size.76.5mm.
Key Type. ME. 14mm

A quick and easy way to cut clean holes in sheet metal up to 16 gauge.

Special design allows even load during cutting and produces a burr free hole that needs no extra finishing.

Heat treated cutting edges with black anti-corrosive surface finish to prevent rusting.

All punches are sold singly without key, which should be ordered separately.

Thread the punch onto the Allen screw and then pass the Allen screw through the hole. Position the die on top of the die nut and then screw the die nut onto the projecting Allen screw until it touches the metal sheet.  Use an Allen key to turn the Allen screw.  The screw will pull the punch through the metal and a hole will result.

Please note these instructions apply to cutters up to 15mm in size, for cutters 15mm and over have a different configuration.  Notably they have fewer components, in the larger cutters the thread is in the punch and thus there is no die nut.

Size.80.0mm.
Key Type.ME. 14mm